How to Create and Delete VLAN on Cisco Catalyst Switch?
Virtual Local Area Networks (VLANs) are used in computer networks to divide a physical network into many logical networks, enhancing security, flexibility, and scalability. This article will walk you through the steps of adding and removing VLANs from a Cisco Catalyst Switch.
Steps To Create and Delete VLAN on Cisco Catalyst Switch
Step 1: Open the Command Line Interface (CLI) of the Switch. You must use the Cisco Catalyst Switch’s Command Line Interface to setup VLANs. This may be accomplished with a console cable or remotely using Telnet or SSH.
Step 2: Enter Privileged EXEC Mode. Once you’ve accessed the CLI, enter privileged EXEC mode by running the following command and entering the necessary password:
switch> enable
Step 3: Navigate to the Global Configuration Mode. Type the following command to enter global configuration mode:
switch# configure terminal
Step 4: Create a VLAN.Use the following command to create a VLAN:
switch(config)# vlan ‘<vlan_id>’
Substitute <vlan_id> with the required VLAN number. For instance, to create VLAN 10, enter:
switch(config)# vlan 10
Step 5: Copy the code switch(config)# vlan 10. Give the VLAN a name. Use the following command to give the VLAN a descriptive name:
switch(config-vlan)# name <vlan_name>
Substitute <vlan_name> with required name. As an example:
switch(config-vlan)# name Sales
Step 6: VLAN Interface Configuration (Optional). You can construct a VLAN interface if you wish the VLAN to have Layer 3 capabilities. The following command should be used:
switch(config)# interface vlan ‘<vlan_id>’
<vlan_id> should be replaced with the VLAN number you want to setup. To configure VLAN 10, for example, use:
Switch(config)# vlan 10 interface
Then, using the ip address command, assign an IP address to the VLAN interface.
Step 7: Assign the VLAN’s ports. Use the following command to add ports to the VLAN.
switch(config)# interface ‘<interface_id>’
Replace ‘<interface_id>’ with the name of the VLAN interface you wish to attach. To attach interface FastEthernet 0/1 to VLAN 10, for example, use:
Switch(config)# interface FastEthernet 0/1
Switch(config-if)# access switchport mode
Switch(config-if)# access switchport vlan 10
Step 8: Check the Configuration. Use the following commands to confirm that the VLAN has been formed and the ports have been appropriately assigned:
switch# show vlan
switch# show interfaces switchport
These commands will display the VLAN information as well as the interface status.
Step 9:For Delete a VLAN use the following command.
switch(config)# no vlan <vlan_id>
Replace ‘< vlan_id>’ with the VLAN number to be removed. To remove VLAN 10, for example, type:
switch(config)# no vlan 10
Different Approaches To VLANs
- VLAN Trunking Protocol (VTP): VTP enables automated VLAN configuration dissemination across numerous network switches.
- VLAN Routing: VLAN routing is the process of routing traffic between VLANs utilising Layer 3 switches or routers.
- VLAN Security: By separating critical resources and instituting access control, VLANs may be utilised to improve network security.
Applications of VLAN
- Network Segmentation: VLANs offer network segmentation, allowing distinct departments or projects to have their own isolated network environments.
- Broadcast Control: VLANs limit the scope of broadcast traffic, which reduces network congestion and improves overall performance.
Advantages of VLAN
- Security: VLANs can segregate critical data, restricting unauthorised access and decreasing the attack surface.
- Improved Network Performance: VLAN segmentation minimises broadcast traffic, which improves network performance.
- Scalability: VLANs provide flexible network growth without requiring physical reconfiguration.
Disadvantages of VLAN
- Complexity: Configuring and administering VLANs may be difficult, necessitating networking knowledge and careful planning.
- Administrative Overhead Increased: VLANs may need greater administrative work for maintenance, monitoring, and troubleshooting.
- Limited Broadcast Domain:A tiny broadcast domain might get saturated if VLANs are not appropriately constructed, reducing network performance.
Conclusion
Creating and removing VLANs on a Cisco Catalyst Switch is a critical network management operation. You can efficiently manage VLANs to optimise network performance and security by following the step-by-step guidance and learning the fundamentals, subtopics, applications, benefits, and drawbacks.
Contact Us